What Size Should A Printed QR Code Be?



When a QR code is published it should be of a size that's appropriate for the scanning environment where it's located. The finished printed size of the QR code is dependent on:

  • The distance between the QR code and the scanning device - which determines the size of the QR code in the viewport of the phone camera
  • The size of the dots in the code - the more data you put into the code the smaller the dots become

Scan Distance

To effectively scan the QR code it should appear to be at least 1cm (0.4 inches) across in the viewport of the scanning device, and as the distance between the camera and the QR code increases, the size of the QR code needs to increase to compensate.

If you have a QR code on the side of a building it needs to be very large because it's going to be scanned from a long distance, however if it's printed in a magazine then the scanning device is held quite close to it so it can be much smaller.

For most smartphones the relationship between scan distance and minimum QR code size is approximately 10:1 so a 2.5cm (1 inch) QR code printed in a magazine has a nominal effective scan distance of about 250mm (10 inches), and a QR code on a billboard 20 metres (65 feet) from where a passer-by scans it probably needs to be about 2 metres (6.5 feet) across. There's a bit of latitude here depending on the sort of smartphone but 10:1 is a good rule of thumb for a well-lit black and white QR code being scanned front-on.

Simple Formula:Minimum QR Code Size = Scanning Distance / 10

If you have a poorly lit or obliquely positioned QR code, or a coloured one where the foreground/background colour contrast might not be optimal, you should probably reduce this ratio to 8:1 or less (ie; the QR code size should 1/8th or less of the scan distance).

QR Code Data Density

As mentioned above, the more data you put into the code the smaller the dots (the dark pixel squares) become as the QR code adjusts itself to increase its data storage capacity.

The density of the code is described by a version number that is based on the number of rows and columns of dots. A Version 1 QR code has 21 rows and 21 columns of dots and the version number then increases by 1 for every 4 extra rows and columns - a Version 2 QR code has 25 rows and columns, a Version 3 has 29 rows and columns, right through to a Version 25 that has 117 rows and columns.

As the size of the dots decrease they become harder for the scanner in the smartphone to "see" so the QR code itself needs to be made larger in order for it to be reliably scanned.

Most QR codes containing just a website address end up being Version 2 QR codes with 25 rows and columns of data dots. I talked about keeping the size of the QR code in the viewport of the scanning to 1cm (0.4in) or better - with 25 rows and columns of dots in a "normal" QR code this makes each of the dots 0.4mm (0.016in) across as a minimum, and this is the "magic number" that makes a QR code reliably scannable.

It was probably a bit simplistic to say that the QR code image should be at least 1cm (0.4in) across in the viewport of the camera - what I should have said was that each of data dots should be at least 0.4mm (0.016in) across, and there's how the data density of the QR code affects its scanning reliability. A QR code with a high data density has more rows and columns of dots in it, so each dot is smaller relative to the size of the QR code itself. If the dots are too small then the QR code is difficult to scan because the data dots are below the resolution limit of the scanning device.

Version 2, Version 6 and Version 10 QR Codes

QR codes containing long URLs (like Google Maps address URLs) may result in up to a Version 6 or Version 7 QR code with 41 or 44 rows and columns of dots.

QR codes containing vCard contact details have notoriously high data densities and result in Version 10 or Version 11 QR codes with more than 60 rows and columns of dots.

To keep each data dot at the recommended 0.4mm (or greater) when viewed in the viewport of the camera you need to make the QR code image itself significantly larger.

HINT: Using a URL shortener to reduce the number of characters in a long URL results in a code with larger dots and hence it can be reproduced at a smaller size without impacting scan reliability.

Calculating The Size

The recommended minimum size of the QR code image is determined by the scanning distance and the size of the data dots in the QR code, and can be calculated by first determining:

  • Distance Factor: Start off with a factor of 10, then reduce it by 1 for poor lighting in the scan environment, a mid-light coloured QR code being used, or the scan not being done front-on.
  • Data Density Factor: Count the number of columns of dots in the QR code image and then divide that by 25 to normalise it back to the equivalent of a Version 2 QR code.
Better Formula:

Minimum QR Code Size = (Scanning Distance / Distance Factor) * Data Density Factor


A QR code containg vCard contact details has resulted in a Version 10 QR code with 57 rows and columns of data dots. It's to be printed on a business card in black and white and it's expected that the scanning distance will be about 150mm.

Scanning Distance = 150mm (5.9 inches)
Distance Factor = 10
Density Factor = 57/25 = 2.28

Minimum Size = (150mm / 10) * 2.28 = 34.2mm (1.34 inches)

A QR code is to be placed behind the counter of a restaurant containing a simple link to a coupon download. The QR code is Version 2 so it has 25 rows and columns of dots. The lighting is a bit dim and the scan distance will be 2.5m.

Scanning Distance = 2500mm (8.2 ft)
Distance Factor = 10 - 1 (for poor lighting) = 9
Density Factor = 25/25 = 1.0

Minimum Size = (2500mm / 9) * 1.0 = 277.7mm (0.91 ft)

A QR code containing a Google Maps location link is to be published in a magazine. This has resulted in a Version 6 QR code (41 rows and columns of data dots) and it will be printed in mid-blue to match the business colours. It's expected that the scan distance will be about 200mm.

Scanning Distance = 200mm (7.9 inches)
Distance Factor = 10 - 1 (for use of colour) = 9
Density Factor = 41/25 = 1.64

Minimum Size = (200mm / 9) * 1.64 = 36.4mm (1.44 inches)

Test, Test, Test...

Regardless of the size of the QR code, the finished QR code should be tested thoroughly in its intended final setting to make sure that it works at that size.

Subscribers Get More QR Stuff!

Become a QR Stuff paid subscriber and get unlimited QR codes, unlimited scans, analytics reporting, editable dynamic QR codes, high resolution and vector QR code images, batch processing, password-protected QR codes, QR code styling, QR code pausing and scheduling and more, for one low subscription fee.

Full subscriptions start from just $11.95 for a 1 month subscription (lower monthly rates for longer periods) and we have a 7-day money-back guarantee. Subscribe now.

Pricing Plans



0 Comment on ‘What Size Should A Printed QR Code Be?’

To top